the airbag has been deployed.
the vehicle is heavily braked from a speed of more than 70 km/h to a standstill.
When you pull away again, the hazard warning light system will switch off automatically at approximately 10 km/h. You can also switch off the hazard warning light system using button .
A fire extinguisher may impede pedal travel or block a depressed pedal.
This jeopardises the operating and road safety of the vehicle.
The fire extinguisher can be flung around and injure the driver or other vehicle occupants.
The safety vests are located in the stowage compartments in the driver and front passenger door.
There are also safety vest compartments in the rear door stowage compartments in which safety vests can be stored.
The requirements defined by the legal standard are only fulfilled if the safety vest is the correct size and is fully closed.
the reflective strips are damaged or dirty
the maximum permissible number of washes is exceeded
the fluorescence has faded
First-aid kit (soft sided) is in the boot in the left-hand or right-hand stowage net, depending on the model.
The QR code is secured in the fuel filler flap and on the opposite side on the B-pillar. In the event of an accident, rescue services can use the QR code to quickly find the appropriate rescue card for your vehicle. The current rescue card contains the most important information about your vehicle in a compact form, e.g. the routing of the electric lines.
Further information can be obtained at Mercedes-Benz homepage - rescue card.
The vehicle is secured with the electric parking brake.
Automatic transmission: the transmission is in position .
Manual transmission: the transmission is in neutral.
The ignition and all electrical consumers are switched off.
The bonnet is open.
When the starting assistance/charging process is complete:
If your vehicle has been started with starting assistance, it may not be possible to use the electric drive for approximately 30 minutes.
Further information can be obtained at a qualified specialist workshop.
If you manipulate or bridge a faulty fuse or if you replace it with a fuse with a higher amperage, the electric line could be overloaded.
This could result in a fire.
Electrical components or systems may be damaged by incorrect fuses, or their functionality may be significantly impaired.
Blown fuses must be replaced with fuses of the same rating, which you can recognise by the colour and fuse rating. The fuse ratings and further information to be observed can be found in the fuse assignment diagram.
Fuse assignment diagram: on the fuse box in the boot More.
Moisture may cause damage to the electrical system or cause it to malfunction.
If the newly inserted fuse also blows, have the cause traced and rectified at a qualified specialist workshop.
The vehicle is secured against rolling away.
All electrical consumers are switched off.
The ignition is switched off.
A flat tyre severely affects the driving characteristics as well as the steering and braking of the vehicle.
Tyres without run-flat characteristics:
Tyres with run-flat characteristics:
Vehicles with MOExtended tyres: it is possible to continue the journey for a short period of time. Make sure you observe the notes on MOExtended tyres (run-flat tyres) More.
Vehicles with a TIREFIT kit: you can repair the tyre so that it is possible to continue the journey for a short period of time. To do this, use the TIREFIT kit More.
Vehicles with Mercedes me connect: you can make a call for breakdown assistance via the overhead control panel in the case of a breakdown More.
All vehicles: change the wheel More.
Apart from some country-specific variants, vehicles are not equipped with a tyre-change tool kit. For more information on which tyre-changing tools are required and approved for performing a wheel change on your vehicle, consult a qualified specialist workshop.
Jack
Chock
Wheel wrench
Centring pin
The jack weighs approximately 2.1 kg.
The maximum load capacity of the jack can be found on the sticker affixed to the jack.
The jack is maintenance-free. If there is a malfunction, please contact a qualified specialist workshop.
The tyre-change tool kit is located under the boot floor.
Apart from some country-specific variants, vehicles are not equipped with a tyre-change tool kit. For more information on which tyre-changing tools are required and approved for performing a wheel change on your vehicle, consult a qualified specialist workshop.
Jack
Chock
Wheel wrench
Centring pin
The jack weighs approximately 2.1 kg.
The maximum load capacity of the jack can be found on the sticker affixed to the jack.
The jack is maintenance-free. If there is a malfunction, please contact a qualified specialist workshop.
The tyre-change tool kit is located under the boot floor.
Apart from some country-specific variants, vehicles are not equipped with a tyre-change tool kit. For more information on which tyre-changing tools are required and approved for performing a wheel change on your vehicle, consult a qualified specialist workshop.
Jack
Chock
Wheel wrench
Centring pin
The jack weighs approximately 2.1 kg.
The maximum load capacity of the jack can be found on the sticker affixed to the jack.
The jack is maintenance-free. If there is a malfunction, please contact a qualified specialist workshop.
The tyre-change tool kit is located in tool bag .
Jack
Wheel wrench
Centring pin
Folding chock
Ratchet for jack
The TIREFIT kit is located under the boot floor.
LK1 – 12 V/10 A, 120 W, 0.8 kg
LK2 – 12 V/15 A, 180 W, 0.9 kg
You can find information on the power category (LK) and/or electrical data on the back of the tyre inflation compressor.
The tyre inflation compressor is maintenance-free. If there is a malfunction, please contact a qualified specialist workshop.
The TIREFIT kit is located under the boot floor.
LK1 – 12 V/10 A, 120 W, 0.8 kg
LK2 – 12 V/15 A, 180 W, 0.9 kg
You can find information on the power category (LK) and/or electrical data on the back of the tyre inflation compressor.
The tyre inflation compressor is maintenance-free. If there is a malfunction, please contact a qualified specialist workshop.
the engine cannot be started
the electric parking brake cannot be released or applied
vehicles with automatic transmission: the automatic transmission cannot be shifted to position or
Vehicles with automatic transmission: if the automatic transmission cannot be shifted to position , or the multifunction display in the instrument cluster does not show anything, have the vehicle transported away More. A towing vehicle with lifting equipment is required for vehicle transportation.
The drivetrain could be damaged when towing at excessively high speeds or over long distances.
the towing eye may become detached.
the vehicle/trailer combination may swerve or even overturn.
If a vehicle must be tow-started or towed away, its permissible gross weight must not exceed the permissible gross weight of the towing vehicle.
the ignition is switched off.
the brake system or power steering system is malfunctioning.
the energy supply or the on-board electrical system is malfunctioning.
When your vehicle is then towed away, significantly more effort may be required to steer and brake than is normally required.
If you pull away sharply, the tractive power may be too high and the vehicles could be damaged.